Deactivation of the Flap-Track Fairing

TASK 57-55-00-040-001-A
Deactivation of the Flap-Track Fairing

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:

DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.

1. Reason for the Job
CDL 27-01
Flap Track Fairing
To remove the fairing and/or connections from the flap-track beam after a fairing has become damaged or missing.

NOTE: Only one fairing must be removed.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	SAFETY BARRIER(S)
No specific	1	TAPE - 3M CONDUCTIVE ELEC(X-1181-COPPER OR X-1170-ALU)
No specific	AR	TIE WRAP(S)
No specific	AR	WARNING NOTICE(S)
98D27803500001	1	LOCKING TOOL ZERO POS

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.05RAB9)	Adhesive Film Tape-- Aluminium Foil -

C. Referenced Information

REFERENCE	DESIGNATION
TASK 12-22-27-640-004-A	Lubricate all Carriage Rollers on all Flap Tracks
TASK 27-50-00-866-009-A	Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01	Retraction of the Flaps/Slats on the Ground
TASK 57-55-11-000-001-A	Removal of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-000-004-A	Removal of the Flap Track Fairings Nos. 2, 3 and 4
ESPM 203333
Safety of the Flap Interconnect- Strut Electrical Harness ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 57-55-00-941-055-A

A. Safety Precautions
(1) Put the WARNING NOTICE(S) in the cockpit to tell persons not to operate the flaps or slats.
(2) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.

Subtask 57-55-00-860-050-A

B. Aircraft Maintenance Configuration
(1) Make sure that the flaps are fully retracted (Ref. AMM TASK 27-50-00-866-009).
(2) Install the 98D27803500001 LOCKING TOOL ZERO POS on the flap/slat control lever.
(3) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable flap track 2, 3 or 4, zone 531(631), 532 (632) or 533(633).

Subtask 57-55-00-865-058-A

C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C ALL
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

4. Procedure
Subtask 57-55-00-040-052-B ** ON A/C NOT FOR ALL

A. Deactivation of the Flap-Track Fairing
(1) Remove the damaged flap-track fairing (Ref. AMM TASK 57-55-11-000-001).
(2) For the track 2 position:

CAUTION: DO NOT TIGHTEN THE CABLE TIE THAT IS USED AS A GUIDE FOR THE ELECTRICAL HARNESSES. IF THE TIE IS TOO TIGHT, THE HARNESSES CANNOT MOVE WHEN THE FLAPS ARE EXTENDED OR RETRACTED.

(a) Examine the electrical harnesses for correct condition.
(b) Install two layers of the conduit at position 1 ESPM 203333.
(c) Safety the conduits at distances of 100 mm (3.9370 in.) with the TIE WRAP(S).
(d) Apply TAPE - 3M CONDUCTIVE ELEC(X-1181-COPPER OR X-1170-ALU) or Adhesive Film Tape-- Aluminium Foil - (Material No.05RAB9) around the electrical conduits at position 2.
(e) Attach the electrical harnesses with a cable tie at position 3. Make sure that you do not fully tighten the cable tie.
(f) After each flight, you must examine the electrical harnesses and the interface connectors to make sure that:

There is no damage to the electrical harnesses.
There is no chafing of the electrical harnesses.
The interface connectors are correctly attached and are not damaged.

(3) After each flight, make sure that the lubrication of the deactivated flap-track assembly is satisfactory (Ref. AMM TASK 12-22-27-640-004).
(4) Make an entry in the aircraft log to tell that you deactivated the flap-track fairing.

Subtask 57-55-00-040-052-C ** ON A/C NOT FOR ALL

A. Deactivation of the Flap-Track Fairing

Safety of the Flap Interconnect- Strut Electrical Harness ** ON A/C NOT FOR ALL

(1) Remove the applicable damaged fairing (Ref. AMM TASK 57-55-11-000-004).
(2) For the track 2 position:

CAUTION: DO NOT TIGHTEN THE CABLE TIE THAT IS USED AS A GUIDE FOR THE ELECTRICAL HARNESSES. IF THE TIE IS TOO TIGHT, THE HARNESSES CANNOT MOVE WHEN THE FLAPS ARE EXTENDED OR RETRACTED.

(a) Examine the electrical harnesses for correct condition.
(b) Install two layers of the conduits at position 1 ESPM 203333.
(c) Safety the conduits at distances of 100 mm (3.9370 in.) with TIE WRAP(S).
(d) Install a TAPE - 3M CONDUCTIVE ELEC(X-1181-COPPER OR X-1170-ALU) or an Adhesive Film Tape-- Aluminium Foil - (Material No.05RAB9) around the electrical conduits at position 2.
(e) Attach the electrical harnesses with a cable tie at position 3. Make sure that you do not fully tighten the cable tie.
(f) After each flight, the electrical harnesses and the interface connectors, must be examined to make sure that:

there is no damage to the electrical harnesses
there is no chafing of the electrical harnesses
the interface connectors are correctly attached and are not damaged.

(3) After each flight, make sure that the lubrication of the deactivated flap-track assembly is satisfactory (Ref. AMM TASK 12-22-27-640-004).
(4) Make a note in the aircraft log that the flap-track fairing has been deactivated.

5. Close-up
Subtask 57-55-00-865-059-A

A. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B07
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1	6CV	B02
** ON A/C ALL
121VU	FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2	8CV	Q21

Subtask 57-55-00-942-050-A

B. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Remove the safety barriers.
(4) Remove the access platform(s).
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.02 06:31:24 UTC