W DOC AIRBUS | AMM A320F

Detailed Inspection of the Cruise Rollers of the Inboard and Outboard Flaps

TASK 57-53-00-220-024-A
Detailed Inspection of the Cruise Rollers of the Inboard and Outboard Flaps

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
  • MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
CAUTION: DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) ON THE INSPECTION AREA. IF YOU APPLY TPS ON THE INSPECTION AREA, YOU CAN CAUSE DAMAGE TO THE AIRCRAFT.
ZONE: 581
ZONE: 587
ZONE: 681
ZONE: 687
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific
1
FLASHLIGHT
No specific
1
MIRROR - INSPECTION
No specific
AR
SAFETY BARRIER(S)
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
AR
WARNING NOTICE(S)
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
581
FLAP N° 1
587
FLAP N° 2
681
FLAP N° 1
687
FLAP N° 2
 D. Expendable Parts
FIG.ITEM
DESIGNATION
IPC-CSN
1
ROLLER
AIPC 57-52-21-15-320
1
ROLLER
AIPC 57-53-23-14-054
2
BEARING
AIPC 57-53-23-14-142
 E. Referenced Information
REFERENCE
DESIGNATION
TASK 27-50-00-866-008-A
Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01
Extension of the Flaps/Slats on the Ground
TASK 27-50-00-866-009-A
Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01
Retraction of the Flaps/Slats on the Ground
TASK 27-54-61-000-002-A
Removal of the Flap Kink-Seals and Cushion-Seals
TASK 27-54-61-400-006-A
Installation of the Flap Kink-Seals and Cushion-Seals
TASK 51-78-00-916-001-A
Application of Temporary Protection System (TPS)
F Cruise Rollers of the Inboard and Outboard Flaps
3. Job Set-up
Subtask 57-53-00-941-102-A
A. Safety Precautions
   (1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
Subtask 57-53-00-860-137-A
B. Aircraft Maintenance Configuration
   (1) Fully extend the flaps (Ref. AMM TASK 27-50-00-866-008).
   (2) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is installed on the flap/slat control lever.
   (3) Put the WARNING NOTICE(S) in position in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-53-00-865-148-A
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB07
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB02
** ON A/C ALL
121VUFLIGHT CONTROLS/FLP/CTL AND/MONG/SYS28CVQ21
Subtask 57-53-00-010-099-A
D. Get Access
   (1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position below the applicable wing.
   (2) Remove the flap kink seals (Ref. AMM TASK 27-54-61-000-002).
Subtask 57-53-00-110-102-A
E. Preparation of the Inspection Area
   (1) Make sure that inspection area is sufficiently clean to do a satisfactory inspection of the area.
   (2) If not, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
   (3) Make sure that there is no TPS layer and if there is a TPS layer, remove it (Ref. AMM TASK 51-78-00-916-001).
4. Procedure
Subtask 57-53-00-220-072-A
A. Inspection of the Cruise Rollers of the Inboard and Outboard Flaps
   (1) If necessary, use the FLASHLIGHT and/or the MIRROR - INSPECTION to do this procedure.
   (2) Examine the cruise rollers of the outboard flap for wear:
     (a) Measure the wear of the cruise rollers:
       1 Make sure that wear F is not more than 1 mm (0.039 in.).
       2 If wear F is more than 1 mm (0.039 in.), replace the AIPC 57-53-23-14-054 ROLLER (1).
       3 Make sure that wear G is not more than 1 mm (0.039 in.).
       4 If wear G is more than 1 mm (0.039 in.), replace the AIPC 57-53-23-14-142 BEARING (2).
   (3) Examine the cruise roller of the inboard flap for wear:
     (a) Measure the wear of the cruise roller:
       1 Make sure that wear F is not more than 1 mm (0.039 in.).
       2 If wear F is more than 1 mm (0.039 in.), replace the AIPC 57-52-21-15-320 ROLLER (1).
5. Close-up
Subtask 57-53-00-410-098-A
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Install the flap kink seals (Ref. AMM TASK 27-54-61-400-006).
Subtask 57-53-00-865-149-A
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB07
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB02
** ON A/C ALL
121VUFLIGHT CONTROLS/FLP/CTL AND/MONG/SYS28CVQ21
Subtask 57-53-00-860-138-A
C. Aircraft Maintenance Configuration
   (1) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap/slat control lever.
   (2) Fully retract the flaps (Ref. AMM TASK 27-50-00-866-009).
Subtask 57-53-00-860-139-A
D. Removal of the Equipment
   (1) Remove the WARNING NOTICE(S).
   (2) Remove the access platform(s).
   (3) Remove the SAFETY BARRIERS.
   (4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
[Rev.10 from 2021] 2026.04.02 06:31:20 UTC
AVIA BRAIN PRODUCTION 2026